大气气溶胶粒子光吸收系数的测量

 采用核孔过滤膜累积气溶胶粒子的方法设计了气溶胶粒子光吸收系数的测量系统。该系统由双光路组成,可以减小光路损耗和电路噪声带来的各种测量误差。同时，具有体积小、光路易于调节、可进行实时测量、定标容易等特点。用200和400nm孔径的过滤膜，分别测量了实验室内大气气溶胶粒子对不同波长激光的吸收系数。随着累积时间的增加，系统的测量精度也不断的提高，在累积时间为900s时，系统测量误差为9.849×10^-6/m。     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。     

PV型HgCdTe光电探测器中的混沌及其诊断

 对激光辐照半导体光电探测器的实验研究，发现当一束不太强的稳定连续波激光照射在PV型HgCdTe光电探测器上时，可以引起探测器出现混沌行为。利用光电探测器的光电压信号随时间变化的实验数据，通过求功率谱、计算Lyapunov指数对混沌进行了诊断。     

等厚双层涂层材料受集中力作用的平面问题理论解

界面应力的正确评价是分析薄膜涂层材料力学特性的难题之一。利用镜像点法和Dirichlet等值性原理，本文推导了等厚双层薄膜涂层材料受表面集中力作用的平面问题理论解。该显式理论解是以固定在各镜像点上的局部坐标系下的Goursat应力函数的形式给出的。对应于高阶镜像点的应力函数，可通过递推的方法，从对应于低阶镜像点的应力函数求得，而且也易于计算机编程。随着镜像点阶数的增大，它与界面的距离也越来越大，因而相对应的应力函数对界面应力的影响越来越小。最后的算例表明，只需考虑前面有限个镜像点，便可获得足够精度的解。该理论解可作为格林函数，以求解复杂问题的理论解，也可用作边界元法的基本解，提高数值计算的精度和效率。     

溶胶-凝胶法制备铁酸盐超微粒子催化剂

采用溶胶－凝胶法制备了含Zn,Ni,Co的铁酸盐超微粒子催化剂，运用DTA－TG、IR、XRD以及BET比表面测试等手段对所制备的样品进行了表征。同时，考察了铁酸盐对二氧化碳选择性氧化乙苯制苯乙烯的催化性能。结果表明：制备的铁酸盐均为尖晶石型晶体，粒子的比表面积为31．9－36．3m^2/g，晶粒大小约为30－35nm，在由二氧化碳选择性氧化乙苯制苯乙烯的反应中表现出较好的催化活性。     

5-Br-PADAP直接光度法测定发锌

为建立一种简便、快速、灵敏的直接光度法测定发锌,将发样经无机化处理后,以5-Br-PADAP作为显色剂,在表面活性剂存在下直接光度法测定头发锌含量。结果表明,该法线性范围为0～612.0μmol/L,回收率为99.4％～102.4％,批内变异系数(CV)和批间变异系数分别为0.027和0.033。55例健康人头发锌含量为171.8±67.5μg(x±2s)。可见5-Br-PADAP直接光度法测定发锌具有操作简单、快速灵敏、结果可靠的优点,适合临床应用。     

制备纳米氧化锌的新方法

以草酸和醋酸锌为原料，用室温固相化学反应首先制备前驱物二水合草酸锌，后者在微波场辐射分解得到产物纳米氧化锌。用XRD，TEM和IR等技术对产物的组成，大小及形貌进行了表征。结果表明：产物纳米氧化锌为粒度分布均匀的球形六角晶系结构，平均粒径约为8nm。     

Morphology and thermal properties of a PC/PE blend with reactive compatibilization

Reactive compatibilization of immiscible polymers is becoming increasingly important and hence a representative study of a polycarbonate/high density polyethylene (PC/HDPE) system is the focus of this paper. A grafted copolymer PC‐graft‐ethylene‐co‐acrylic acid (PC‐graft‐EAA) was generated as a compatibilizer in situ during processing operation by ester and acid reaction between PC and ethylene‐acrylic acid (EAA) in the presence of the catalyst dibutyl tin oxide (DBTO). As the polyethylene (PE) matrix does not play any part during the synthesis of the copolymer and since PC and EAA are also immiscible, to simplify the system, the influence of this copolymer formation at the interface between PC and EAA on rheological properties, phase morphology, and crystallization behavior for EAA/PC binary blends was first studied. The equilibrium torque increased with the DBTO content increasing in EAA/PC blends on Haake torque rheometer, indicating the in situ formation of the graft copolymer. Scanning electron microscopy (SEM) studies of cryogenically fractured surfaces showed a significant change at the distribution and dispersion of the dispersed phase in the presence of DBTO, compared with the EAA/PC blend without the catalyst. Differential scanning calorimetry (DSC) studies suggested that the heat of fusion of the EAA phase in PC/EAA blends with or without DBTO reduced with the formation of the copolymer compared with pure EAA. Then morphological studies and crystallization behavior of the uncompatibilized and compatibilized blends of PC/PE were studied as functions of EAA phase concentration and DBTO content. Morphological observations in PC/PE blends also revealed that on increasing the EAA content or adding the catalyst DBTO, the number of microvoids was reduced and the interface was intensive as compared to the uncompatibilized PC/PE blends. Crystallization studies indicated that PE crystallized at its bulk crystallization temperature. The degree of crystallinity of PE phase in PC/PE/EAA blends was also reduced with the addition of EAA and DBTO compared to the uncompatibilized blends of PC/PE, indicating the decrease in the degree of crystallinity was more in the presence of PC‐graft‐EAA. Copyright © 2007 John Wiley & Sons, Ltd.     

Determination of Fibre Pore Structure: Influence of Salt,pH and Conventional Wet Strength Resins

It has been shown, in the present investigation, that the two methods used to investigate the pore size distribution of unbleached chemical pulps, i.e. inverse size exclusion chromatography (ISEC) and nuclear magnetic resonance (NMR), give different average pore radius for the pores inside the fibre wall. This is due to the way in which these experiments are performed and the sensitivity of the methods to different types of pores in the cell wall. It was also shown that the two methods gave different results when changing the pH and the ionic strength of the pulp suspension. The pore radius, as detected with ISEC, decreased with both increasing ionic strength and decreasing pH, indicating a loose structure of the exterior of the fibrillar network. However, the pore radius as detected with NMR, was virtually unaffected when increasing the ionic strength, indicating a very rigid structure of the interior of the fibre wall. Decreasing pH though, lead to a decrease in pore radius indicating that upon protonation of the carboxylic groups in the fibre wall, the electrostatic repulsion is diminished and the average pore radius decreases. The NMR technique was also used to study wet strength aid penetration into the fibre wall. It was shown that wet strength aids with a small molecular weight, penetrated the fibre wall, as detected by a decrease in pore radius. It was also shown that addition of different wet strength aids increased the tensile index of the sheet and decreased the fibre strength, measured as zero span-strength of the sheets.